{"product_id":"radium-catch-can-kits-nissan-s13","title":"Radium - Direct-Fit Catch Can Kits for Nissan S13 (Silvia \/ 180SX \/ 240SX SR20DET)","description":"\u003cp\u003eThe catch can draws out oil and water condensation from the crankcase gasses that would otherwise be drawn into the intake manifold. This prevents oil buildup in the intake, intercooler system walls, throttle body, and intake manifold. This effectively raises the octane, can increase engine performance from cleaner inlet air, and can lower hydrocarbon emissions. The closed system prevents unwanted oil vapors from entering into the cabin. Catch can kits include everything needed for a complete installation.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eFLUID LOCK® CATCH CANS\u003c\/h3\u003e\n\u003cp\u003eIn 2022, Radium Engineering implemented a revolutionary design change to the 7 fluid ounce standard catch can. An inherent problem always existed with typical catch cans when not serviced regularly. The fluid contaminants will eventually leave the reservoir pouring into the air intake system causing poor engine performance. To resolve this issue, Radium created the Fluid Lock® Catch Can. This contains a patented mechanism that prevents the reservoir from overfilling and traps the collected fluids until it is emptied.\u003c\/p\u003e\n\u003cp\u003e\u003cimg class=\"myImages\" id=\"myImg\" style=\"width: 240px;\" src=\"https:\/\/www.radiumauto.com\/cdn\/shop\/files\/FL3_a_Internals.jpg\"\u003e\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eCOLLECTION \u0026amp; EMPTYING\u003cbr\u003e\n\u003c\/h3\u003e\n\u003cp\u003eThe rate that your catch cans will collect oil and moisture contaminants will vary from one individual vehicle to the next, so there is no set emptying interval. PCV catch cans tend to collect more than CCV catch cans. You should check the level of your catch can using the integrated dipstick starting at 3-4 weeks of driving and repeat as needed to determine how often they should be emptied based on what you see.\u003c\/p\u003e\n\u003cp\u003eCatch cans can be emptied by unscrewing the lower reservoir and removing it from the vehicle to dump out, or in cases where there is available space under the catch can, the \u003ca href=\"\/products\/radium-catch-can-petcock-drain-kit\"\u003ePetcock Drain Kit\u003c\/a\u003e can be installed and used to drain them.\u003c\/p\u003e\n\u003cp\u003eIn cases where oil collection is excessive you may have to address an issue with the engine. The reasons a catch can will collect an excess of oil include\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eExcessive blowby from engine damage\u003c\/li\u003e\n\u003cli\u003eCrankcase windage from an over-full oil level\u003c\/li\u003e\n\u003cli\u003ePoor placement of breather ports and\/or poor baffling inside breather ports\u003c\/li\u003e\n\u003cli\u003ePCV valve not closing and leaking under heavy load\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cdiv class=\"spec-box3\"\u003e\n\u003ch4\u003e20-0725-FL Catch Can Kit PCV Nissan S13\u003c\/h4\u003e\n\u003cdiv style=\"float: left; width: 200px;\"\u003e\u003cimg src=\"https:\/\/www.radiumauto.com\/cdn\/shop\/files\/20-0725-FL.jpg\" style=\"width:200px;\" id=\"myImg\" class=\"myImages\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"poptext\"\u003e\n\u003cp\u003eThe PCV catch can kit runs inline between the PCV valve and the intake manifold. It mounts to threaded bosses on the RH strut tower just clear of the fuel filter.\u003c\/p\u003e\n\u003cp\u003eWhen the intake manifold pressure is close to or greater than atmospheric pressure, the PCV valve closes and this hose experiences no flow. The PCV hoses will experience metered vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNOTES\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe PCV catch can kit is compatible and recommended to be used with the CCV catch can kit. See 20-0726 below.\u003c\/li\u003e\n\u003cli\u003eNo extra inline check valve is required since Radium catch cans are pressure sealed.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"spec-box3\"\u003e\n\u003ch4\u003e20-0726-FL Catch Can Kit CCV Nissan S13\u003c\/h4\u003e\n\u003cdiv style=\"float: left; width: 200px;\"\u003e\u003cimg src=\"https:\/\/www.radiumauto.com\/cdn\/shop\/files\/20-0726-FL.jpg\" style=\"width:200px;\" id=\"myImg\" class=\"myImages\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"poptext\"\u003e\n\u003cp\u003eThe CCV catch can mounts to 2 holes in the LH side of the unibody near the firewall. It was designed specifically to clear the windshield wiper motor (RHD) and the master cylinders (LHD).\u003c\/p\u003e\n\u003cp\u003eTo retain factory functionality, the CCV catch can runs inline between the crankcase vent (CCV) port and the intake pipe. At low loads, it experiences atmospheric pressure. However, when the engine is at high load (WOT), the line will experience high flow from the crankcase into the intake system. This would normally lead to oil and sludge accumulation in the air filter intake pipe. This oil accumulation would spread and be found in the intercooler which lowers the thermal efficiency properties of the heat exchanger and leads to decreased performance. The CCV catch can captures this and promotes clean filtered air back into the intake.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cem\u003eNOTES:\u003c\/em\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe CCV catch can kit does NOT address blow-by from the PCV valve side of the crankcase.\u003c\/li\u003e\n\u003cli\u003eThe CCV catch can kit is compatible and recommended to be used with the PCV catch can kit. See 20-0725 above.\u003c\/li\u003e\n\u003cli\u003eThe kit is designed to connect the provided hose to the OEM valve cover barb. However, an add-on a la carte option (not included) for the SR20DET is outlined below. Nothing else is required.\u003cbr\u003e1x \u003ca href=\"\/products\/radium-Swivel-Press-In-Fittings-Nissan-Valve-Covers\"\u003e20-0811 10AN Press-In Fitting\u003c\/a\u003e\u003cbr\u003e1x \u003ca href=\"\/products\/radium-PushLok-Hose-Ends\"\u003e14-0215 10AN Hose End, 180deg\u003c\/a\u003e\u003cbr\u003e1x \u003ca href=\"\/products\/radium-PushLok-Hose-Ends\"\u003e14-0211 10AN Hose End, Straight\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"spec-box3\"\u003e\n\u003ch4\u003e20-0727-FL Dual Catch Can Kit Nissan S13\u003c\/h4\u003e\n\u003cdiv style=\"float: left; width: 200px;\"\u003e\u003cimg src=\"https:\/\/www.radiumauto.com\/cdn\/shop\/files\/20-0727-FL.jpg\" style=\"width:200px;\" id=\"myImg\" class=\"myImages\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"poptext\"\u003e\n\u003cp\u003eFor the ultimate in engine protection, Radium recommends Dual Catch Can Kit. This kit utilizes both the PCV and CCV catch can kits detailed above.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\n\u003cdiv style=\"border-left: 3px solid #e11d48; background: rgba(225, 29, 72, 0.05); padding: 12px 16px; margin: 20px 0; border-radius: 4px; font-size: 0.9em; color: #881337;\"\u003e\n  \u003cstrong\u003eNotice:\u003c\/strong\u003e This product is designed and intended strictly for off-road closed-course motorsport competition and racing vehicles.\n\u003c\/div\u003e","brand":"Radium Engineering","offers":[{"title":"PCV Side Catch Can Kit","offer_id":50528615727262,"sku":"20-0725-FL","price":333.0,"currency_code":"CAD","in_stock":true},{"title":"CCV Side Catch Can Kit","offer_id":50528615760030,"sku":"20-0726-FL","price":348.0,"currency_code":"CAD","in_stock":true},{"title":"Dual Catch Can Complete Kit (PCV + CCV)","offer_id":50528615792798,"sku":"20-0727-FL","price":667.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6460\/0734\/files\/radium-catch-can-kits-nissan-s13-1.jpg?v=1790278022","url":"https:\/\/dm-performance.ca\/products\/radium-catch-can-kits-nissan-s13","provider":"DM Performance","version":"1.0","type":"link"}